214 lines
8.3 KiB
Plaintext
214 lines
8.3 KiB
Plaintext
* Rockchip rk3399 DMC (Dynamic Memory Controller) device
|
|
|
|
Required properties:
|
|
- compatible: Must be "rockchip,rk3399-dmc".
|
|
- devfreq-events: Node to get DDR loading, Refer to
|
|
Documentation/devicetree/bindings/devfreq/event/
|
|
rockchip-dfi.txt
|
|
- clocks: Phandles for clock specified in "clock-names" property
|
|
- clock-names : The name of clock used by the DFI, must be
|
|
"pclk_ddr_mon";
|
|
- operating-points-v2: Refer to Documentation/devicetree/bindings/opp/opp.txt
|
|
for details.
|
|
- center-supply: DMC supply node.
|
|
- status: Marks the node enabled/disabled.
|
|
|
|
Optional properties:
|
|
- interrupts: The CPU interrupt number. The interrupt specifier
|
|
format depends on the interrupt controller.
|
|
It should be a DCF interrupt. When DDR DVFS finishes
|
|
a DCF interrupt is triggered.
|
|
|
|
Following properties relate to DDR timing:
|
|
|
|
- rockchip,dram_speed_bin : Value reference include/dt-bindings/clock/rk3399-ddr.h,
|
|
it selects the DDR3 cl-trp-trcd type. It must be
|
|
set according to "Speed Bin" in DDR3 datasheet,
|
|
DO NOT use a smaller "Speed Bin" than specified
|
|
for the DDR3 being used.
|
|
|
|
- rockchip,pd_idle : Configure the PD_IDLE value. Defines the
|
|
power-down idle period in which memories are
|
|
placed into power-down mode if bus is idle
|
|
for PD_IDLE DFI clock cycles.
|
|
|
|
- rockchip,sr_idle : Configure the SR_IDLE value. Defines the
|
|
self-refresh idle period in which memories are
|
|
placed into self-refresh mode if bus is idle
|
|
for SR_IDLE * 1024 DFI clock cycles (DFI
|
|
clocks freq is half of DRAM clock), default
|
|
value is "0".
|
|
|
|
- rockchip,sr_mc_gate_idle : Defines the memory self-refresh and controller
|
|
clock gating idle period. Memories are placed
|
|
into self-refresh mode and memory controller
|
|
clock arg gating started if bus is idle for
|
|
sr_mc_gate_idle*1024 DFI clock cycles.
|
|
|
|
- rockchip,srpd_lite_idle : Defines the self-refresh power down idle
|
|
period in which memories are placed into
|
|
self-refresh power down mode if bus is idle
|
|
for srpd_lite_idle * 1024 DFI clock cycles.
|
|
This parameter is for LPDDR4 only.
|
|
|
|
- rockchip,standby_idle : Defines the standby idle period in which
|
|
memories are placed into self-refresh mode.
|
|
The controller, pi, PHY and DRAM clock will
|
|
be gated if bus is idle for standby_idle * DFI
|
|
clock cycles.
|
|
|
|
- rockchip,dram_dll_dis_freq : Defines the DDR3 DLL bypass frequency in MHz.
|
|
When DDR frequency is less than DRAM_DLL_DISB_FREQ,
|
|
DDR3 DLL will be bypassed. Note: if DLL was bypassed,
|
|
the odt will also stop working.
|
|
|
|
- rockchip,phy_dll_dis_freq : Defines the PHY dll bypass frequency in
|
|
MHz (Mega Hz). When DDR frequency is less than
|
|
DRAM_DLL_DISB_FREQ, PHY DLL will be bypassed.
|
|
Note: PHY DLL and PHY ODT are independent.
|
|
|
|
- rockchip,ddr3_odt_dis_freq : When the DRAM type is DDR3, this parameter defines
|
|
the ODT disable frequency in MHz (Mega Hz).
|
|
when the DDR frequency is less then ddr3_odt_dis_freq,
|
|
the ODT on the DRAM side and controller side are
|
|
both disabled.
|
|
|
|
- rockchip,ddr3_drv : When the DRAM type is DDR3, this parameter defines
|
|
the DRAM side driver strength in ohms. Default
|
|
value is DDR3_DS_40ohm.
|
|
|
|
- rockchip,ddr3_odt : When the DRAM type is DDR3, this parameter defines
|
|
the DRAM side ODT strength in ohms. Default value
|
|
is DDR3_ODT_120ohm.
|
|
|
|
- rockchip,phy_ddr3_ca_drv : When the DRAM type is DDR3, this parameter defines
|
|
the phy side CA line (incluing command line,
|
|
address line and clock line) driver strength.
|
|
Default value is PHY_DRV_ODT_40.
|
|
|
|
- rockchip,phy_ddr3_dq_drv : When the DRAM type is DDR3, this parameter defines
|
|
the PHY side DQ line (including DQS/DQ/DM line)
|
|
driver strength. Default value is PHY_DRV_ODT_40.
|
|
|
|
- rockchip,phy_ddr3_odt : When the DRAM type is DDR3, this parameter defines
|
|
the PHY side ODT strength. Default value is
|
|
PHY_DRV_ODT_240.
|
|
|
|
- rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines
|
|
then ODT disable frequency in MHz (Mega Hz).
|
|
When DDR frequency is less then ddr3_odt_dis_freq,
|
|
the ODT on the DRAM side and controller side are
|
|
both disabled.
|
|
|
|
- rockchip,lpddr3_drv : When the DRAM type is LPDDR3, this parameter defines
|
|
the DRAM side driver strength in ohms. Default
|
|
value is LP3_DS_34ohm.
|
|
|
|
- rockchip,lpddr3_odt : When the DRAM type is LPDDR3, this parameter defines
|
|
the DRAM side ODT strength in ohms. Default value
|
|
is LP3_ODT_240ohm.
|
|
|
|
- rockchip,phy_lpddr3_ca_drv : When the DRAM type is LPDDR3, this parameter defines
|
|
the PHY side CA line (including command line,
|
|
address line and clock line) driver strength.
|
|
Default value is PHY_DRV_ODT_40.
|
|
|
|
- rockchip,phy_lpddr3_dq_drv : When the DRAM type is LPDDR3, this parameter defines
|
|
the PHY side DQ line (including DQS/DQ/DM line)
|
|
driver strength. Default value is
|
|
PHY_DRV_ODT_40.
|
|
|
|
- rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define
|
|
the phy side odt strength, default value is
|
|
PHY_DRV_ODT_240.
|
|
|
|
- rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter
|
|
defines the ODT disable frequency in
|
|
MHz (Mega Hz). When the DDR frequency is less then
|
|
ddr3_odt_dis_freq, the ODT on the DRAM side and
|
|
controller side are both disabled.
|
|
|
|
- rockchip,lpddr4_drv : When the DRAM type is LPDDR4, this parameter defines
|
|
the DRAM side driver strength in ohms. Default
|
|
value is LP4_PDDS_60ohm.
|
|
|
|
- rockchip,lpddr4_dq_odt : When the DRAM type is LPDDR4, this parameter defines
|
|
the DRAM side ODT on DQS/DQ line strength in ohms.
|
|
Default value is LP4_DQ_ODT_40ohm.
|
|
|
|
- rockchip,lpddr4_ca_odt : When the DRAM type is LPDDR4, this parameter defines
|
|
the DRAM side ODT on CA line strength in ohms.
|
|
Default value is LP4_CA_ODT_40ohm.
|
|
|
|
- rockchip,phy_lpddr4_ca_drv : When the DRAM type is LPDDR4, this parameter defines
|
|
the PHY side CA line (including command address
|
|
line) driver strength. Default value is
|
|
PHY_DRV_ODT_40.
|
|
|
|
- rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines
|
|
the PHY side clock line and CS line driver
|
|
strength. Default value is PHY_DRV_ODT_80.
|
|
|
|
- rockchip,phy_lpddr4_dq_drv : When the DRAM type is LPDDR4, this parameter defines
|
|
the PHY side DQ line (including DQS/DQ/DM line)
|
|
driver strength. Default value is PHY_DRV_ODT_80.
|
|
|
|
- rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines
|
|
the PHY side ODT strength. Default value is
|
|
PHY_DRV_ODT_60.
|
|
|
|
Example:
|
|
dmc_opp_table: dmc_opp_table {
|
|
compatible = "operating-points-v2";
|
|
|
|
opp00 {
|
|
opp-hz = /bits/ 64 <300000000>;
|
|
opp-microvolt = <900000>;
|
|
};
|
|
opp01 {
|
|
opp-hz = /bits/ 64 <666000000>;
|
|
opp-microvolt = <900000>;
|
|
};
|
|
};
|
|
|
|
dmc: dmc {
|
|
compatible = "rockchip,rk3399-dmc";
|
|
devfreq-events = <&dfi>;
|
|
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&cru SCLK_DDRCLK>;
|
|
clock-names = "dmc_clk";
|
|
operating-points-v2 = <&dmc_opp_table>;
|
|
center-supply = <&ppvar_centerlogic>;
|
|
upthreshold = <15>;
|
|
downdifferential = <10>;
|
|
rockchip,ddr3_speed_bin = <21>;
|
|
rockchip,pd_idle = <0x40>;
|
|
rockchip,sr_idle = <0x2>;
|
|
rockchip,sr_mc_gate_idle = <0x3>;
|
|
rockchip,srpd_lite_idle = <0x4>;
|
|
rockchip,standby_idle = <0x2000>;
|
|
rockchip,dram_dll_dis_freq = <300>;
|
|
rockchip,phy_dll_dis_freq = <125>;
|
|
rockchip,auto_pd_dis_freq = <666>;
|
|
rockchip,ddr3_odt_dis_freq = <333>;
|
|
rockchip,ddr3_drv = <DDR3_DS_40ohm>;
|
|
rockchip,ddr3_odt = <DDR3_ODT_120ohm>;
|
|
rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>;
|
|
rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>;
|
|
rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>;
|
|
rockchip,lpddr3_odt_dis_freq = <333>;
|
|
rockchip,lpddr3_drv = <LP3_DS_34ohm>;
|
|
rockchip,lpddr3_odt = <LP3_ODT_240ohm>;
|
|
rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>;
|
|
rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>;
|
|
rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>;
|
|
rockchip,lpddr4_odt_dis_freq = <333>;
|
|
rockchip,lpddr4_drv = <LP4_PDDS_60ohm>;
|
|
rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>;
|
|
rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>;
|
|
rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>;
|
|
rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>;
|
|
rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>;
|
|
rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>;
|
|
};
|